hummer

Vehicle recall defect – Certain Honeywell Fram Racing Brand Hp4 And Hp8 Oil Filters That Were Manufactured From May 25, 2006, Through September 14, 2007, And Sold For Use As Replacement Equipment For Vehicles List Above. The Affected Filters Are Marked With A Date Code A61451 Through A72571 Sequentially. The Date Code And Part Number Appear On The Filter Housing. Fram Racing Hp4 And Hp8 Oil Filters Not Bearing A Date Code In This Range Are Not Affected By This Recall. The Gasket Of The Oil Filter Becomes More Pliable Under High Temperatures And Pressures.

Vehicle recall defect – Certain Replacement Fuel Filters, Fram Brand Name P/N G3727, With Date Codes X52911 Through X60801 Sequentially Or X600141 And A Mexico Country Or Origin Marking On The Fuel Filter Housing Manufactured From October 18, 2005, Through March 21, 2006, Sold For Use On The Vehicles Listed Above And On Certain School Buses. (To See The School Bus Engine Sizes, Click On “Document Search” And Then “Bus Applications”). The Connector On The Fuel Filter Was Not Manufactured To Honeywell’S Specification. As A Result, The O-Ring May Not Seat Correctly On The Fuel Line.

Vehicle recall defect – The Coating Used To Protect The Accelerator Pedal Shaft Is Incompatible With The Bronze Bushing Through Which The Shaft Passes. Over Time, And In The Presence Of A Corrosive Environment (Water, Road Salt), The Shaft Can Corrode Inside The Bushing Increasing The Amount Of FriCTIon Between The Rotating Shaft And The Stationary Bushing.

Vehicle recall defect – Water Can Accumulate In The Cruise Control Cable And If The Outside Temperature Is Below Freezing And The Cruise Control Is Engaged, The Water Can Freeze Causing The Cable To Bind And Not Release As Intended When The Brake Pedal Is Applied Or The System Is Turned Off At The Master Cruise Control Switch.

Vehicle recall defect – The Oil Pressure Switch Which Controls The Power To The Electric Fuel Pump Can Fail. Failure Is Due To A Missing Rubber Seal Between The Switch And The Wiring Harness. The Missing Seal Allows Contaminants To Enter The Switch Causing It To Fail In The Open Or Closed Position.

Vehicle recall defect – Certain Honeywell Fram Racing Brand Hp4 And Hp8 Oil Filters That Were Manufactured From May 25, 2006, Through September 14, 2007, And Sold For Use As Replacement Equipment For Vehicles List Above. The Affected Filters Are Marked With A Date Code A61451 Through A72571 Sequentially. The Date Code And Part Number Appear On The Filter Housing. Fram Racing Hp4 And Hp8 Oil Filters Not Bearing A Date Code In This Range Are Not Affected By This Recall. The Gasket Of The Oil Filter Becomes More Pliable Under High Temperatures And Pressures.

Vehicle recall defect – Certain Honeywell Fram Racing Brand Hp4 And Hp8 Oil Filters That Were Manufactured From May 25, 2006, Through September 14, 2007, And Sold For Use As Replacement Equipment For Vehicles List Above. The Affected Filters Are Marked With A Date Code A61451 Through A72571 Sequentially. The Date Code And Part Number Appear On The Filter Housing. Fram Racing Hp4 And Hp8 Oil Filters Not Bearing A Date Code In This Range Are Not Affected By This Recall. The Gasket Of The Oil Filter Becomes More Pliable Under High Temperatures And Pressures.

Vehicle recall defect – Vehicle Description: Sport Utility Vehicles. The Turn Signal Switch Plastic Cancellation Pin Can Wear Prematurely Causing The Signals To Fail To Cancel After Completing A Turn.

Vehicle recall defect – Certain Honeywell Fram Racing Brand Hp4 And Hp8 Oil Filters That Were Manufactured From May 25, 2006, Through September 14, 2007, And Sold For Use As Replacement Equipment For Vehicles List Above. The Affected Filters Are Marked With A Date Code A61451 Through A72571 Sequentially. The Date Code And Part Number Appear On The Filter Housing. Fram Racing Hp4 And Hp8 Oil Filters Not Bearing A Date Code In This Range Are Not Affected By This Recall. The Gasket Of The Oil Filter Becomes More Pliable Under High Temperatures And Pressures.

Vehicle recall defect – Vehicle Description: Buses Equipped With Isringhausen Seats In The Driver Position. Two Welds Located On The Back Rest Adjustment Side Of The Seat Frame Did Not Meet The Manufacturer’S Specifications.