laramie

Coleman Laramie (1986) – 86V095000

Vehicle recall defect – Valve Stem May Become Unseated While Burner Control Knob Is Being Turned Allowing Gas To Escape. Consequence Of Defect: Gas Seepage Around The Base Of The Valve Stem Could Result In A Fire.


Laramie P20575B14 – 85T006000

Vehicle recall defect – Tires Fail To Meet Requirements Of Endurance Test Fmvss # 109. Failure Was Due To Higher Than Specified Second Ply Angle. Consequence Of Defect: The Incorrect Second Ply Angle Caused Chafing Of Plies In The Bead Base Area. A Chafed Ply Can Result In Sudden Air Loss And Vehicle Crash May Occur Without Prior Warning.


Laramie P20570R15 – 98T002000

Vehicle recall defect – Tire Description: P205/70R14 And P205/70R15 Tires, Serial Numbers Beginning With “Pj” And Ending With A Combination Of 136 Through 367. The Tire Brands Involved Are: Big O Legacy Tour Plus, Embassy Diplomat, Arizonian Limited Edition, Kelly Aqua Tour, Ultra Touring Gt, Telstar PremiUM Touring, Laramie PremiUM Touring, Jetzon Ultra Quad +, Sears Superguard Ft, Motomaster Sk110, Co-Op Golden Mark, Cordovan Grand Prix, Shell Touring 2000, Multi-Mile Grand Am, Sigma Supreme Touring, Concorde Touring 9000, And Summit Touring Tlr For Both Size Tires. Unical Touring Radial And Pos-A-TrAction Tires Are In Size P20570R15 Only. A Circumferential Cracking Condition In The Lower Sidewall Above The Bead Area Can Occur.


Laramie P20570R14 – 98T002000

Vehicle recall defect – Tire Description: P205/70R14 And P205/70R15 Tires, Serial Numbers Beginning With “Pj” And Ending With A Combination Of 136 Through 367. The Tire Brands Involved Are: Big O Legacy Tour Plus, Embassy Diplomat, Arizonian Limited Edition, Kelly Aqua Tour, Ultra Touring Gt, Telstar PremiUM Touring, Laramie PremiUM Touring, Jetzon Ultra Quad +, Sears Superguard Ft, Motomaster Sk110, Co-Op Golden Mark, Cordovan Grand Prix, Shell Touring 2000, Multi-Mile Grand Am, Sigma Supreme Touring, Concorde Touring 9000, And Summit Touring Tlr For Both Size Tires. Unical Touring Radial And Pos-A-TrAction Tires Are In Size P20570R15 Only. A Circumferential Cracking Condition In The Lower Sidewall Above The Bead Area Can Occur.


Laramie P19575R14 – 94T007000

Vehicle recall defect – An Insufficient Cure Condition In The Bead Wire Rubber Insulation Was Caused By A Small Amount Of Contaminated Rubber.


Laramie P18575R14 – 94T007000

Vehicle recall defect – An Insufficient Cure Condition In The Bead Wire Rubber Insulation Was Caused By A Small Amount Of Contaminated Rubber.


Laramie P16580R13 – 89T006000

Vehicle recall defect – Tires May Develop A Separation Between Plies During Service As A Result Of Lower Adhesion Due To Ply Coat Stock That Was Off- Specification.


Laramie Laramie Performer Hp – 06T017000

Vehicle recall defect – Certain Treadways Tires Of Various Models Listed Above Manufactured Between August 6 And August 19, 2006 (Dot Serial Weeks 3206 And 3306.) Some Of The Subject Tires May Have Been Produced With Non-Conforming Belt Wire Coat Stock. If Placed In Service, The Subject Tires May Develop A Belt Separation Due To A Reduced Ability To Prevent Corrosion Of The Steel Wires In An Instance Where Moisture Reaches The Steel Belt.


Laramie Laramie Performer A/T – 08T006000

Vehicle recall defect – TBC Corporation Is Recalling 17,014 Various Load Range E Tires, Size Lt265/75R16, Produced Between December 2, 2007 And February 2, 2008. These Tires Fail To Conform To The Requirements Of Federal Motor Vehicle Safety Standard No. 139, New Pneumatic Radial Tires For Light Vehicles. After Testing, A Bulge Can Occur In The Lower Sidewall On The White Sidewall Side Which Indicates The Existence Of A Separation Between Two Lower Sidewall Components.


Laramie Laramie Grandeur Classic – 06T017000

Vehicle recall defect – Certain Treadways Tires Of Various Models Listed Above Manufactured Between August 6 And August 19, 2006 (Dot Serial Weeks 3206 And 3306.) Some Of The Subject Tires May Have Been Produced With Non-Conforming Belt Wire Coat Stock. If Placed In Service, The Subject Tires May Develop A Belt Separation Due To A Reduced Ability To Prevent Corrosion Of The Steel Wires In An Instance Where Moisture Reaches The Steel Belt.